mk@mk-AMILO-Pa-1510:~/Schreibtisch$ dmesg | egrep 'net|eth|sky|sun|sis|via|3c3|3c5|e100|8139|8169|acx|air|ath|atl|ar9|carl|atme|at7|herm|iwl|ipw|rtl8|r81|rt2|rt3|rt6|rt7|tg3|ssb|wl|b43|b44|ori|pri|p5|zd|ndis|wmi|ns8|FW'
[ 0.000000] original variable MTRRs
[ 0.000000] BRK [0x01fe1000, 0x01fe1fff] PGTABLE
[ 0.000000] Ignoring ACPI timer override.
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff880097a00000 s86336 r8192 d24256 u1048576
[ 0.000000] pcpu-alloc: s86336 r8192 d24256 u1048576 alloc=1*2097152
[ 0.000000] Aperture beyond 4GB. Ignoring.
[ 0.184226] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.196068] pci 0000:05:05.0: [10ec:8139] type 00 class 0x020000
[ 0.923653] audit: initializing netlink socket (disabled)
[ 1.180810] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.180814] ACPI: Thermal Zone [THRM] (25 C)
[ 1.191191] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.328395] Loaded X.509 cert 'Magrathea: Glacier signing key: 5e3c0f9ca6e36543535fa2bb5b709e84f16da7c7'
[ 1.581130] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 1.581214] 8139cp 0000:05:05.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 1.587372] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 1.589205] 8139too 0000:05:05.0 eth0: RealTek RTL8139 at 0x000000000001a000, 00:03:0d:54:03:a5, IRQ 9
[ 17.566249] Adding 2488316k swap on /dev/sda6. Priority:-1 extents:1 across:2488316k FS
[ 17.662683] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.039250] ath5k 0000:05:03.0: registered as 'phy0'
[ 19.591491] fbcon: radeondrmfb (fb0) is primary device
[ 20.326325] ath: EEPROM regdomain: 0x30
[ 20.326339] ath: EEPROM indicates we should expect a direct regpair map
[ 20.326345] ath: Country alpha2 being used: AM
[ 20.326350] ath: Regpair used: 0x30
[ 20.384064] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 20.391111] ath5k: phy0: Atheros AR2413 chip found (MAC: 0x78, PHY: 0x45)
[ 20.540125] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 22.968838] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 23.009369] 8139too 0000:05:05.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
[ 25.018268] audit_printk_skb: 102 callbacks suppressed
[ 26.583183] wlan0: authenticate with 14:da:e9:f9:4a:ec
[ 26.588967] wlan0: send auth to 14:da:e9:f9:4a:ec (try 1/3)
[ 26.590537] wlan0: authenticated
[ 26.592132] wlan0: associate with 14:da:e9:f9:4a:ec (try 1/3)
[ 26.594644] wlan0: RX AssocResp from 14:da:e9:f9:4a:ec (capab=0xc11 status=0 aid=3)
[ 26.595261] wlan0: associated
[ 26.595339] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1874.260090] raid6: using algorithm sse2x4 (1444 MB/s)
[ 1874.260095] raid6: using intx1 recovery algorithm
[ 2488.408492] 8139too 0000:05:05.0 eth0: link down